Did you know?

2. Corroded Battery Post. A corroded battery post can easily create a condition where your Santa Fe hesitates to start. It also happens to be the easiest thing to check on this list. With that in mind take a look real quick and see if there’s any corrosion or battery acid on the battery cables or post.This is expected and "normal". When the brake pedal is hard you need to push the pedal much much harder to get the ignition system to enable. If the engine is cranking but still not starting/firing after several attempts, hold the gas pedal to the floor. Holding the pedal to the floor turns off the fuel injectors and allows the "flooding ...Repair procedures. Removal PODS-F ODU (Occupant Detection Unit) 1. Disconnect the battery negative cable, and wait for at least three minutes before beginning work. 2. …1) have a super hard brake pedal 2) have everything else turn on including bluetooth, fan, etc. 3) not crank / click or anything for starting The dealership did NOT find anything wrong the first time and couldn't replicate the issue. This time, the car won't start and has been sitting in a parking lot for 3 days waiting to get towed.The brake pedal is hard and car won’t start when I push the button. Some of the lights in the right gauge turn on and - Answered by a verified Hyundai Mechanic ... Hyundai 2013 Santa Fe sport...Won't start. Electronics work, power windows, fans etc all work...but when I press brake pedal and then start button there is just clicking and ...I did a little research online and a couple people recommended holding the push start down for 25 secs. So this morning leaving to work it wouldn't start so I tried that method and it started. I called the Hyundai dealership and have an appt. tomorrow to get it checked out. From complaints on the forums it looks like it might be the "brake ...2004 Santa Fe 3.5 will not start. So I'm at wits end here. Vehicle ran fine no issues. Went to replace the master cylinder and it would not go over 2000 rpm or 20mph. Replaced the tps and the fuel pump as well as the plugs. I am not getting any codes.4) Exit the car and close the door, 5) Activate the security lock, and wait 2-3 minutes, 6) Unlock the door with security lock, 7). Fully depress the brakes and make certain the car’s transmission is in park, before starting the car. 8) Wait 20-30 sec. to allow all the systems to boot before driving the car.It happend again to me again today. Brake Pedal is real stiff, wont move. I finally stood on the **** pedal with all my weight (and im a fat @$$) and it started and soon as it did the pedal instantly returned to normal. Dealer wont acknowledge this is a issue, but im afraid the brakes may act up while im driving.Duralast Gold Ceramic Brake Pads DG1432. Part # DG1432. SKU # 158240. Limited-Lifetime Warranty. Check if this fits your 2010 Hyundai Santa Fe. Location: Front. Notes: Ceramic, *OE Performance with smooth, quiet stopping power, ultra-low dust. PRICE: 42.99.Prerequisites for ISG System Activation: The driver's seatbelt is fastened. The driver's door and the hood are closed. The brake vacuum pressure is adequate. The battery is sufficiently charged, State of Charge (SOC) is 70% or above. The outside temperature is between 14 ~ 95oF (-10 ~ 35o C) The engine coolant temperature is over 86oF (30o C)To resolve Hyundai push button start issues, consider the following tips based on the provided sources: Check the Brake Pedal Sensor: A common issue is the failure of the brake pedal sensor, which prevents the car from recognizing that the brake pedal is pressed, a necessary condition to start the car. Inspecting and possibly replacing the ...2007 Hyundai Santa Fe Brake Disc Hardware Kit - Rear; 2007 Hyundai Santa Fe Brake Caliper Bolt / Guide Pin Kit; Show Less. Related Makes. Toyota Brake Pads; ... Which is the Brake Pedal? Why is My Brake Pedal Hard to Push? How to Adjust Drum Brakes; Brake Pads vs Brake Shoes; Is Brake Fluid Leaking from the Caliper?My 2013 Santa Fe Sport 2.0T is having intermittent starting problems. Have a look at the video I recorded. To me, it feels like the power going to the starter is dropping out just before the motor can turn over. This happens every other time and the car often starts like it should on the first try. What you see in the video is at its worst and ...To resolve Hyundai push button start issues, consider the following tips based on the provided sources: Check the Brake Pedal Sensor: A common issue is the failure of the brake pedal sensor, which prevents the car from recognizing that the brake pedal is pressed, a necessary condition to start the car. Inspecting and possibly replacing the ...

*2007 Hyundai Santa Fe Limited 3.3L, 125k miles Aug 2015 ... Got the wheels back on, dropped the car, and then went to the front and depressed the emergency brake pedal 3 times, per Hyundai's instruction. ... and then afterward attempted to tighten the adjusting wheel inside each of the rear brake drums and it still won't lock up the …So I have to remove the key, wait some time and try again. Usually, it can take 3-4 times (and up to 15 minutes!) before the key-symbol light comes up again in the dash, and then the engine will start as if nothing ever happened. This problem occurs approximately once a week, but you never know when.Hi, I have a 2003 hyundai Santa Fe that has had a problem for a few years that I can not figure out, nor can the hyundai dealership. (Though they seem to only want to hook it up to a computer, which tells them that nothing is wrong.) After filling up the car with gas, the car will turn over, but will stall immediately. You can press on the gas and it will stay going, but once you take your ...Asked by Iggimore Sep 29, 2013 at 09:01 PM about the 2004 Hyundai Sonata. Question type: Maintenance & Repair. My car runs fine normally with no issues stalling or killing the motor. When I need to put gas in my car it will not start. I have to crank the motor until it starts but it will stall immediately unless I put my foot on the gas pedal ...Vacuum is only generated when the engine is running, which is why your brake pedal always feels a 'little' bit hard when the engine is off, only to soften (or 'puff') as the car starts. If the pedal feels so hard that you can't engage the engine, or continues to feel hard after the car starts, you may have a leak in your vacuum system.

The car was towed/repaired for 782. In this article, well cover the reasons why the pedal becomes stiff and later on explore the fixes to release the brake pedal and get your car started. more. Thats better than any other plug-in hybrid in the market. If your Santa Fe wont start, be happy if you see the check engine light.There could be various reasons behind your Hyundai Santa Fe's brake pedal pulsation. Understanding these causes is crucial for timely and effective solutions. This section will discuss a few possible reasons that can lead to brake pedal pulsation in your Hyundai Santa Fe. Wheel Bearings. Another possibility is loose or worn wheel bearings.A Mazda 3 refusing to start with a locked brake could be due to numerous reasons. These include issues with the ignition, brake pedal, key fob, electrical system, starter motor, battery, ABS, immobilizer, fuse, or transmission. It is recommended to consult a professional mechanic to diagnose and rectify the problem accurately.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. 1. Weak Battery. If your Elantra’s engine won’t crank or crank. Possible cause: 1) have a super hard brake pedal 2) have everything else turn on includin.